Email format error
Email cannot be empty
Email already exists
6-20 characters(letters plus numbers only)
The password is inconsistent
Email format error
Email cannot be empty
Email does not exist
6-20 characters(letters plus numbers only)
The password is inconsistent
Wire Straightener Machine
This straightening machine consists of a frame, a straightening mechanism, and a cutting mechanism. The parts are made of high strength steel plates to ensure the safety of the machine, while being easy to use.
The performance characteristics of the straightening machine:
- The straightening machine consists of a frame, a straightening mechanism, a feeding mechanism, and a cutting mechanism. It is composed of linear guns and wire racks. The casing is made of a high-strength premium steel plate.
- The straightening part is composed of a straightening shaft, a straightening pressing block, and bearing seats at both ends, which completes the straightening of the wire. Its power is the motor installed at the bottom of the frame, which drives the straightening shaft to rotate at high speed through the V-belt.
- The straightening device and the wire feeding cutting device are driven by their respective motors and do not interfere with each other. The two front and rear wire feeding mechanisms can ensure the smooth feeding of the wire and the balance of the machine. Both motors are mounted on the bottom of the machine. It can increase the stability of the machine.
- The wire feeder, cutter, etc. are made of high-quality alloy steel, and through vacuum treatment, it has wear resistance and extended service life. The straightening and pressing blocks are made of cast iron, alloys, plastics, etc.; the shafts are all made of 40CR and are quenched and tempered, and the gears are all made of forged billets, which are quenched and tempered and the tooth surface is high-frequency quenched, and the hardness is as high as HRC55-58 degrees. It is suitable for galvanized wire, powder drawing wire, water drawing wire, and stainless steel wire, which can ensure that the surface of the wire is free from scratches.
- The cutting length can be adjusted arbitrarily, the error is small, and the upper and lower cutting knives with high hardness can make the incision better.
- Square and flat special-shaped straightening blocks can be customized according to customer requirements.
- The machine can be equipped with a preset counter. That is, when the set processing quantity is reached, it will beep and stop automatically.
Installation and commissioning of the straightening machine:
- Installation: During installation, the host and the wire rack should be placed horizontally to ensure stable placement and no shaking. After the long axis and the straight gun are installed, the level needs to be adjusted so that the wire groove of the straight gun and the center line of the main machine inlet hole are on the same line.
- Commissioning: Before the test run, clean the running parts, and then lubricate the inner hole of the guide sleeve and other parts according to the lubrication requirements. During the test run, first, carry out the idling test, control the motor to run forward and reverse during the test, and check whether each part is running normally and whether there is abnormal noise. After confirming that it is reliable, you can start to debug the wire. By adjusting the pressing block and the fixed-length insert, the straightness and the required length are respectively guaranteed, and the work can be started after the requirements are met.
Application range of straightening machine:
Ordinary iron wire, spring steel, water-drawn wire, powder-drawn wire, carbon steel wire, stainless steel wire, copper wire, aluminum wire, cold-drawn wire, galvanized wire, plastic-coated steel wire, and other non-ferrous metal wires are straightened and cut. The cut-off length can be customized according to customer requirements. Widely used in the mesh industry, hardware products, racks, storage cages, shopping carts, electroplating hangers, wire craft products, lighting, springs, bicycle baskets, spokes, storage cages, carts, dust removal skeletons, etc. industry.
Foshan Jinchun Industrial Automation Technology Co., Ltd. was established in 1998. It is a technology-intensive industrial company specializing in the development of welding technology and equipment research and manufacturing, integrating scientific research, production, and sales.
With rich experience and strong technical personnel, the company constantly innovates and develops various types of high-quality hardware wire rods, hardware mesh baskets, and other mechanical equipment. It has formed five series of electric fan and industrial fan guard production lines, wire tube evaporator and condenser production lines, pet cage production line, bag cage frame production line for bag filter, buckle machine, and chain machine production line. The company has accumulated more than ten years of development, production, and operation of welding machines and related products. The products are widely used in the fields of manufacturing and production of hardware appliances, lighting, kitchenware shelves, decorative handicrafts, cultural and sports products, electrical and electronic communication batteries, and industrial equipment automation. With a very wide user group.
The company pursues management to promote efficiency, quality for survival, technology for development, strictly implement the national quality assurance system standards, provide customers with high-quality, stable, and reliable products, and perfect high-quality services. Welcome people from all over the world to visit the company. business, and work together to create a better tomorrow.
